Paint Correction Lighting: Mounting a Light on Your Polisher
You can't correct what you can't see. Swirls, holograms and haze that look gone under the shop lights show up in the sun the next morning. Good overhead lighting helps, but the most useful light during paint correction is the one aimed at the spot where the pad is working.
This post covers why polisher-mounted lighting helps, how to set it up, and how to use it with an inspection routine.
Why light at the pad matters
Defects in clear coat are tiny scratches. You see them when light hits them at an angle and reflects back to your eye. Overhead lights come from one direction, so some defects show and others hide depending on where you stand. As you move the polisher across a panel, the angle keeps changing.
A light mounted on the polisher moves with the pad. Wherever you are working, the light hits that spot from the same angle, so you can watch the defects as you correct them instead of stopping to inspect after every section.
What to look for in a polisher light
- Brightness and a wide beam, so you see the whole work area, not a dot.
- Color temperature. Cooler, bluer light shows fine scratches with more contrast for many people.
- Battery that lasts a working day, so you aren't swapping mid-panel.
- Vibration damping, because polishers shake and lights fail.
- A quick way on and off, for charging and for the times you don't want it.
The Flamethrower III
The Flamethrower III Polishing Light System was built for this job. From the product page:
- 800 lumen wide-angle LED at 7800 Kelvin
- Rechargeable lithium ion battery with 10-12 hours of work time on high
- Fits any polisher with the supplied kit
- Quick disconnect for removal and charging
- Vibration dampener
- Lifetime warranty on the hardware, 12 months on the light
It also comes with a headband with a one-handed snap lock, so the same light works for hands-free inspection or under-dash work.
Setting it up
- Install the hub. The Hub Assembly includes a hub, spacer, star lock washer and an 8mm-10mm bushing, listed for polishers such as Adams, DeWalt and Milwaukee.
- Attach the arm and light. Position it so the beam lands just ahead of and across the pad, not straight down into it.
- Add hubs to your other machines. With a hub on each polisher, you move one light between your rotary, DA and Nano without re-mounting.
Using it during correction
- Test spot first. Light a small section, make your passes, and watch how the defects change. That tells you whether your pad and polish combination is cutting enough.
- Keep the light angle steady. Let the polisher-mounted light do the work. Don't keep repositioning it mid-section.
- Check with a second light source. After each panel, look at it under your overhead or handheld light, or the headband. A different angle catches what the polisher light didn't.
- Final check outside or under a different color temperature before the car goes back to the customer.
Two lights for DA work
Dual action pads oscillate, and some detailers like light from two sides to reduce shadows. The Double Flamethrower III System includes two lights and a free mounting hub; the product page calls it the best kit for a dual action polisher.
Already own a Flamethrower?
The Flamethrower III fits all previous Flamethrower hardware. If you already have the original (bolt-on) or Flamethrower II (snap-on) setup, you can buy just the Flamethrower III Light & Headband. If you have a Gen 1 and want the quick-disconnect setup, the Flamethrower II Conversion Kit with Extra Hub has the arm, anti-vibration mount and two hubs.
Lighting the interior too
The same light mounts to vacuum tools. The Vac-Brite 1.5 in. attachment fits 1.4-1.6 in. round tubes like crevice tools and extractor handles. The Nano-Brite 1.25 in. fits 1-1.3 in. tubes, including the Rupes Nano iBrid. Both require a light kit, sold separately. For shops that do both paint and pet-hair interiors, the Ultimate Flamethrower III Bundle combines the lights and mounts with the Fur Eel tools and the Hammerhead.
The short version
Light where the pad is working shows defects as you remove them. Mount a light on each polisher with a quick-disconnect hub, check each panel under a second light, and do a final inspection under different light before delivery.