Which Fur Eel Adapter Fits My Vacuum?

The most common question we get about the Fur Eel isn't about pet hair. It's about fit: "Will this work on my vacuum?" Usually the answer is yes, with the right adapter. This guide shows you how to measure your vacuum and which Buff Brite part goes with it.

How the system fits together

Every setup has the same pieces:

  1. Your vacuum hose or wand
  2. An adapter, if needed, which matches your hose to the Fang
  3. The Fang Adapter, which holds the tool
  4. The tool: the Fur Eel Pro II or the Hammerhead

The Fang has two fits: 1.25 in. inside diameter and 1.5 in. outside diameter. If your hose matches either, you don't need anything else.

Step 1: Measure your hose end

Take off any attachment so you are looking at the bare end of the hose or wand. Measure across it with a ruler or calipers:

  • Outside diameter if the end slides into tools
  • Inside diameter if tools slide into the hose

Write the number down in inches or millimeters. That number decides everything below.

Step 2: Find your size

Your hose end What to use Notes from the product page
1.25 in. (32 mm) inside, or 1.5 in. outside Fang Adapter only Central vacs, upright vacs with a hose, many wet/dry vacs, garage and shop vacs
Dyson with clip-in attachments Adapter (B) Dyson Adapter Fits the Dyson clip-in system and slides inside the Fang; 1.25 in. (32 mm) outside diameter; "most Dyson vacuum systems"
1 3/8 in. (35 mm) outside Adapter (A) Listed for Shark, Hoover, Miele, Black & Decker and others. Measure to confirm
2.25 in. RIDGID, Shop-Vac or Craftsman hose end Adapter (C) RIDGID/Shop Vac Large end slides over the hose; small end fits into the Fang
1.5 in. to 2 in. (35-50 mm), including 1-7/8 in. RIDGID Vario-Max Twist to adjust the size, then snap on
1.25 in. (32 mm) inside hose, want 1.5 in. tools Adapter (D) non-swivel cuff or Adapter (E) swivel cuff The swivel version keeps the hose from twisting
1.5 in. inside hose, want 1.5 in. tools Adapter (F) 1.5 in. cuff Spins onto the hose; listed for car wash and detailing setups

Kits that include the adapter

If you don't own a Fur Eel yet, a kit saves a step:

Brand notes

Dyson. Use Adapter B. It is made for the Dyson clip-in attachment system. The product page says it fits most Dyson systems, not every model, so check the clip style on yours.

Shark. Many Shark models have a 1 3/8 in. (35 mm) wand end, which takes Adapter A. Shark has changed its wand designs over the years, so measure rather than going by the model name.

Shop-Vac, RIDGID, Craftsman. The large 2.25 in. hose takes Adapter C. For the 1-7/8 in. RIDGID hose, or any hose between 1.5 and 2 in., the Vario-Max adjusts to fit.

Central vacuums. Many have a 1.25 in. inside fitting, which takes the Fang directly. If your hose is 1.25 in. inside and you want to use 1.5 in. tools too, add Adapter D or E.

Car wash vacuums. The Fur Eel slides onto a standard 1.5 in. crevice tool, so you can put it on the car wash nozzle.

The Hammerhead and Sidewinder use the same adapters

The Hammerhead has a 1.5 in. (35 mm) outside and 1.25 in. (32 mm) inside fit, the same as the Fur Eel, so any adapter above works for it. The Sidewinder Crevice Tool has a 1.5 in. outside diameter and comes with a 1.25 in. adapter.

Still not sure?

Send us your measurement and vacuum model, or call 208-800-2050 and a person will help you match it. Buff Brite has sold more than 750,000 units of its pet hair tools, and fit questions are the ones we answer most often.

Back to blog

Leave a comment